• Szanowni Klienci, ze względu na święta w Niemczech, w dniach 3-6 kwietnia 2026 r. wysyłki do Polski nie będą realizowane.

PFERD TOOLS flexible shaft BW 7 PST-T DIN10/M5 2 metres for POLISTAR-Tube 4,250-1,500 RPM/1,000-370 watts

Nr art.: 4007220432372
Cena za 1 Sztuka
plus podatek VAT w obowiązującej wysokości Ceny plus koszty dostawy
Indywidualne ceny dla klientów biznesowych po zalogowaniu.
na zamówienie
Czas realizacji ok. 4-6 dni roboczych
0 sztuk w magazynie

Wybierz rozmiar artykułu i ilość

Cena za 1 Sztuka (z VAT)

Dostępność

UWAGA:
Ten produkt jest zamawiany bezpośrednio u producenta i nie znajduje się w naszym magazynie – czas dostawy może być wydłużony.Ostateczna cena zostanie wyświetlona po dodaniu produktu do koszyka i przejściu do kasy.Produkt nie podlega zwrotowi. Informacje

Dodaj do listy artykułów

Udostępnij ten produkt

lub skopiować ten link

Szczegóły produktu

Identyfikacja i klasyfikacja

Numer artykułu 4007220432372
EAN / GTIN 4007220432372
Numer producenta 87101804
Numer L L51050 1747
Producent/osoba odpowiedzialna August Rueggeberg GmbH & Co. KG, Hauptstraße 13, 51709 Marienheide, Deutschland, www.pferd.com

Opis

Opis:

  • These special flexible shafts do not have a handpiece for tool mounting and are particularly flexible in the front section.
  • The POLISTAR-TUBE grinding tools are attached directly to the core of the flexible shaft with screws (INOX type).
  • POLINOX cross buffs PNST are screwed on with adapter AD M4 or AD M5 (accessories).
  • This combination is highly suitable for gradual fine grinding and cleaning of inner surfaces of pipes and pipe bends.
  • Both pipe bend ends can be deburred from the entry side.
  • The PST-T flexible shaft is suitable for grinding the insides of pipes.
  • The flexible shaft is exclusively for use with POLISTAR-TUBE PST diameter 90 and 100 mm.

Cecha szcz.:

  • PFERD TOOLS type: BW 7 PST-T DIN 10/M5 2m
  • Power range, from: 370 watts
  • Rotational speed range, from: 1500 RPM
  • Rotational speed range, to: 4250 RPM
  • Width, metric: 18 mm
  • Dia. drive-side coupling, metric: 30 mm
  • Drive-side coupling, DIN: 10
  • Power range, to: 1000 watts
  • Length, metric: 2032 mm
  • Net weight: 1.32 kg
  • Dia. drive-side coupling [mm]: 30
  • Dia. external, metric: 18 mm
  • Dia. thread: M5
  • Dia. tool mounting: 5 mm
  • Height: 18 mm

Zastosowanie:

  • Recommendations for use: Flexible shaft motors with stepless rotational speed regulation are recommended as tool drives. Before the POLISTAR-TUBE and the shaft are introduced into the pipe, the tool should be preformed and adjusted to the pipe diameter. At the moment of introduction, it is recommended to reduce the respective operating speed of the POLISTAR-TUBE. The grinding of pipes with more than three bends should be performed from both ends whenever possible. When the tool flaps emerge at the end of the pipe, they can be withdrawn while in rotation. This way, the rear side of the POLISTAR-TUBE deburrs the pipe end and at the same time polishes the inside of the tube during the reverse motion. All flexible shaft drives with rotational speed range 7,650–1,500 RPM and flexible shaft connection DIN 10 can be used. For maintenance of the flexible shaft, PFERD TOOLS recommends the P‐SET BW 7 maintenance set.

W dostawie:

  • Special lengths available on request.

Wskazówka:

  • Observe the recommended and maximum permitted rotational speeds of the tools for the rotational speed setting of the motor.

Pliki do pobrania i dokumenty

Doradcy ds. usług i produktów

Ulotki

If you see this, something went wrong, or you disabled javascript

Formularze

If you see this, something went wrong, or you disabled javascript

Promocje

If you see this, something went wrong, or you disabled javascript

Zaloguj się

Nie masz jeszcze konta w eShop?

Logowanie

Twoja osoba kontaktowa

Ustal prowizję

Karta klienta

Prosimy o okazanie kodu QR przy kasie.
Pobrano w dniu 

W koszyku

Do koszyka
Do koszyka